Skip to main content
  • Research article
  • Open access
  • Published:

Validated green spectrophotometric kinetic method for determination of Clindamycin Hydrochloride in capsules

Abstract

Background

Simple, sensitive, free of organic solvents, kinetic spectrophotometric method has been developed for the determination of Clindamycin Hydrochloride, both in pure form and Capsules. Method is based on reaction of Clindamycin with potassium iodide and potassium iodate in an aqueous medium at (25 ± 2 °C) to produce yellow-coloured tri iodide ions (I3). The reaction is followed spectrophotometrically by measuring the absorbance at wavelength 350 nm during 40 min.

Results

The effects of analytical parameters on reported kinetic methods were investigated. Under the optimized conditions, the initial rate and fixed time (at 10 min) methods were used for constructing the calibration graphs. The graphs were linear in concentration ranges 1–20 μg ml−1 with limit of detection of 0.12 and 0.22 μg ml−1for the initial rate and fixed time methods, respectively. The results were satisfactory and the analytical performance for both methods was validated.

Conclusion

The proposed methods have been applied to determine the components in capsules with an average recovery of 98.25–102.00% and the results are in good agreement with those found by the reference method.

Peer Review reports

Introduction

Clindamycin (CLN), (methyl-7-chloro-6,7,8-trideoxy-6-{[4R)-1-methyl-4-propyl-L-prolyl]amino}-1-thio-L-threo-3-Dgalacto-octopyranoside), is a semi-synthetic analog of lincomycin [1]. (Fig. 1).

Fig. 1
figure 1

Clindamycin Hydrochloride

By binding to the 50S subunit of the ribosome, Clindamycin inhibits the synthesis of bacterial proteins. It is active against Gram-positive aerobic, anaerobic and some Gram-negative aerobic bacteria. [1]

It works similar to a bacteriostatic antibiotic. Common clinical conditions in which they have included the infections of gynaecology, gingiva, respiratory tract, skin, soft tissue, and intra-abdominal infections. Also, Clindamycin is used in pneumonia caused by Pneumocystis, toxoplasmosis, malaria, babesiosis, and acne[2]. Clindamycin is existing in a wide variety of prescription formulations that can be given orally or dermally [2].

There are a variety of analytical techniques to determine Clindamycin in various pharmaceutical formulations, as well as in biological samples.

The United States Pharmacopoeia (USP) suggested the technique of liquid chromatography for the Clindamycin assay [3]. High-performance liquid chromatography (HPLC) is commonly used [4,5,6,7,9], potentiometric determination [10] capillary electrophoresis [11], micellar chromatography [12], chemiluminescence methods [13], voltammetry [14,15,16] and spectrophotometric determination that dependent on color forming [17, 18].

Previous publications reported spectrometric determination of CLN based on the method oxidation of a sulfur atom in acidic medium. Then the absorbance was measured at 520 nm [17]. Other spectrophotometric method includes the formation of ion-pair complex between CLN and rose bengal in faintly basic medium (pH 7.5). The produced colour is measured at 555 nm [18]

The proposed UV–Vis spectrophotometric method allows evaluating the content of CLN in capsules.

There is no research about the determination of CLN based on kinetic methods.

Kinetic methods have benefits such as reduction of interference with excipients, therefore there is a need for a Kinetic Method to determine CLN.

The purpose of this thesis was to report new, simple and accurate kinetic spectrophotometric methods for the determination of CLN.HCl as raw materials and in capsules without interaction with other ingredients in their formulations.

The proposed method is economical and low-cost since it uses inorganic reagents.

Apparatuses

UV–Visible spectrophotometer (JASCO, model V650, Japan).

1.00 cm quartz cells.

An ultrasonic processor (Powersonic, model 405, Korea) was used to sonicate the sample solutions. Adjustable micropipettes covering a volume range from 2 to 2000 μL (ISO-LAB, Germany), used for the preparation of the experimental solutions.

Analytical balance (Sartorius, model 2474, Germany).

Materials

Pharmaceutical grade Clindamycin HCl (99%) were received from XUHUANG, CHINA.

Potassium iodide and potassium iodate (Panreac, Germany).

All chemicals used were analytical grade.

Standard solutions

By dissolving 25 mg of CLN.HCl in 25 ml of double-distilled water, a standard solution (1 mg ml−1) of CLN.HCl was prepared. Appropriate amounts of KI and KIO3 were dissolved in water for preparing solutions with a concentration of 0.3 M and 0.2 M, respectively.

The solutions were stable for a time of 2 days when stored at (5 °C).

Approaches

General Procedure for Kinetic Study

Increasing amounts of CLN.HCl standard solution (1 mg.ml−1) have been moved to 10 ml volumetric flasks containing 3 ml KI (0.3 M) and 1 ml KIO3 (0.2 M).

The volume was completed to the mark with water.

The absorbance of the prepared solutions was measured at different times 0, 5, 10,15, 20, 25, 30, 35 and 40 min. The λmax was 350 nm.

At room temperature (25 ± 2 °C), the measurements were carried out.

Procedure for calibration

Initial rate method

Initial reaction rates were measured by calculating the slopes of the initial tangent to the absorbance time curves.

To reach concentrations between (0.5–30) μg ml−1 of CLN.HCl, aliquots of the CLN.HCl research solution is pipetted into 10 ml regular flasks.

In each flask, 3 ml of KI (0.3 M) and 1 ml of KIO3 (0.2 M) were added. Then they were diluted with distilled water to the mark.

The contents of each flask's mixture were well mixed.

The growth in absorbance was listed as a function of time at 350 nm. From the slope of the tangent to the absorbance-time curve, the initial reaction rate (n) at different concentrations was obtained.

Fixed time method

In this method, the absorption of yellow-coloured solutions containing deferent quantities of the drug was measured at a certain fixed time, 10 min, as defined above for the initial rate method.

Calibration structure

To construct a calibration curve, the absorbance information of kinetic tracks at 0 min and 40 min are used. The average relative responses of 5 repeats were estimated. Absorbance that comes between 98 to 102% of the average relative response is only included in the calibration curve construction For each drug, the limits of Beer's law, slope, intercept, coefficient of correlation and regression equation are brief in Table 1.

Table 1 The regression equation and Linear range for CLN.HCl at a fixed time and 25 ̊ C

Method validation

In terms of accuracy, precision and detection limits, the innovative method for estimating the drug has been validated.

Absorbance-time curves were drawn, and the substance recovery was measured using the initial rate and fixed time method.

The analyses have been replicated at least 5 times to assess the precision, and accuracy is measured in terms of percent recovery and percent RSD. The precision and accuracy of the procedures are demonstrated by strong percent recovery; the RSD was less than 2.

T-test and F-test values were both calculated using a reference method.

The t-test and F-test values are in the acceptable range, reflecting the methods' high accuracy and precision (Table 2).

Table 2 Parameters of the fixed time method (600 s)

Method selectivity and ruggedness

The excipients of each product were added to the pure drug sample. The recovery experimentations were performed. Ruggedness is method resistance for a minor variation such as apparatus and expert, or both. 3 different instruments and 2 analysts were reported to test the robustness of the absorption method results. No important changes were detected either by apparatus or analyst alteration.

Procedure for pharmaceutical formulations

The content of twenty separate capsules was weighed up. An accurately weighed quantity of the powder equivalent to 50 mg of CLN.HCl was moved into a volumetric flask and dissolve in 50 ml of water. The content was sonicated for 10 min. A portion of this solution was centrifuged for 15 min at 5000 rpm, a suitable volume of the supernatant was moved into a 10 ml volumetric flask and procedure were continued to use for the analysis of CLN.HCl by the proposed spectrophotometric method.

Results

Iodide ions transform to free iodine in an aqueous medium which has acidic properties, the acidity comes from HCl. Free iodine reacts with an excess of iodide ions and produces a yellow complex. The complex consists of iodide (I3) (Fig. 2) [19, 20].

$${{\text{IO}}}_{{3}}^{ - } + {8} {{\text{I}}}^{ - } + {6} {{\text{H}}}^{ + } \to {3} {{\text{I}}}_{{3}}^{ - } + {3} {{\text{H}}}_{{2}} {{\text{O}}}$$
Fig. 2
figure 2

(1) Blank (I + KI) against distilled water, (2) CLN.HCl (5 μg ml−1) + 3 ml of 0.30 M KI + 2.0 ml of 0.1 M KIO3 against Blank, (3) CLN against water

Optimum conditions for interaction.

The ideal conditions for the improvement of the method were recognized by changing the parameters one at a time and keeping the others fixed and observing the influence produced on the absorbance of the coloured products. [19]

A volume of 3 ml of 0.3 M KI, 1 ml of 0.1 M KIO3 were found to be optimum for maximum colour advance for an estimate of CLN.HCl.

At the mentioned parameters, the results indicate that the absorbance value at 25 ◦C was maximum.

Calibration graphs

The colour that appears in the solutions when the drug interacts with the reagents increases over time. This phenomenon can be used in a kinetic study to determine clindamycin.

The methods of the initial rate, rate constant, fixed absorbance and fixed time were studied.

Fixed time method and initial rate method were adopted due to accuracy, precision and linear range.

Therefore, the two methods were used for constructing the calibration and to determine CLN.HCl.

Absorption changes were studied at λmax (360 nm), for CLN-reagent solutions versus time (Other conditions were stable), as shown in Fig. 3—the concentration range of (1–20)mg/L-

Fig. 3
figure 3

Absorbance—time curve for CLN.HCL + reagent (KI + KIO3), Concentrations of CLN.HCL:: (1)1 ppm; (2)2 ppm; (3)4 ppm;(4)8 ppm; (5)12 ppm, (5)16 ppm, (6) 20 ppm

Initial rate method

The initial reaction rate was determined from the slope of the tangent to the absorption time curve at different concentrations. By plotting the logarithm of the initial reaction rate against the logarithm of the molar CLN.HCl concentration, the calibration graph was constructed.

The rate data of reaction would follow a pseudo order rate constant and submitted the following rate equation: [19]

$$\upsilon = \frac{{\Delta {\text{C}}}}{{\Delta {\text{t}}}} = \frac{{\Delta {\text{A}}}}{{\Delta {\text{t}}}} = {\text{K}}.{\text{C}}^{{\text{n}}}$$

where:

ν: reaction rate, A: absorbance., ∆A = At2 − At1, t is the measuring time, ∆t = t2 − t1, K is the pseudo order rate constant, c is the concentration of (CLI) mol/L and n is the order of the reaction. [21]

A calibration curve was constructed by plotting the logarithm of the initial rate of reaction (log ν) against the logarithm of (CLN.HCl) concentration (log c), which showed a linear relationship over the concentration range of (1–20) mg/L (Fig. 4). [22]

Fig. 4
figure 4

logarithm (ΔA/Δt) versus the logarithm of (CCLN) curve.

The equation of the curve can be written as follows:

$${\text{log v }} = {\text{ log }}\Delta {\text{A}}/\Delta {\text{t }} = {\text{ log k}}^{\prime} + {\text{ n logc}}$$
$${\text{log v }} = {\text{ Log }}\Delta {\text{A}}/\Delta {\text{t }} = \, 0.{\text{9722 log c }} - { 1}.{4793}$$

The reaction is the first order (n = 0.9722 = 1) regarding to Clindamycin concentration, k' = 30.15 s−1.

Rate constant method

The logarithm of the absorbance contrasted with time for each concentration of CLN.HCL which investigated over the concentration range of 1–20 mg/L was estimated.

In the range of 1–8 mg/L (1.570 × 10−4_ 2.355 × 10–4) M, graphs of log absorbance against time were plotted for CLN.HCl concentration. The pseudo order rate constant (k') corresponding to CLN.HCl concentrations are determined from the slopes multiplied by-2,303[21]. The results are shown in (Fig. 5).

Fig. 5
figure 5

Rate constant method calibration curve for CLN.HCl

c against k' equation: \({\text{y}} = \, 5.6352{\text{x }} - \, 21.459 \, \left( {{\text{ R}} \, = \, 0.6234} \right)\).

Fixed absorbance method

The absorbance was fixed at the value 1.2, then the time required to reach this value was calculated in seconds for several concentrations of (CLN.HCl) in the range 10–20 mg/L.

It was found that the chosen value intersects with the curves of the absorbance change as a function of time.

Then the graph representing the changes in the time value of 1/t versus the concentration of ClN.HCl was plotted (Fig. 6).

Fig. 6
figure 6

Graph for determining CLN.HCl by fixed absorbance method

Subsequently, the equation of the calibration graph was found:

$${1}/{\text{t }} = { 693}.{\text{99C }} - \, 0.0{157}\left( {{\text{r }}0.{8452}} \right)$$

Fixed time method

At specific times, the absorption of the solutions containing varying amounts of CLN against a blank solution was measured.

Graphically. The curve was built by representing absorption values versus the concentration of (CLN.HCl) at a preselected time of 0–2400 s (40 min).

The correlation coefficient, slope and intersection value were determined at each time, and these values are shown in Table 1. The most acceptable value and which had the best R-value was obtained.

Consequently, a fixed time of 600 s was selected to determine (CLN.HCl). (Fig. 7).

Fig. 7
figure 7

Graph for determining CLN.HCl by fixed time method (t = 10 min)

Evaluate the validity of the proposed method

Calibration graph

The Correlation coefficient, intercept and slope values for the calibration data were determined by using the least square method [20]. The most appropriate values of the correlation coefficient were found for the reaction at 600 s as a fixed time, which was chosen as the best and most efficient time for doing the measurements and determine the drug (Table 2).

Reaction conditions were stated, then a fixed time method was used to estimate CLN.HCl in a range of concentration of 2–12 mg / L. Limit of determination that can be detected (LOD) was found by the proposed method, the limit of quantification was also found (LOQ) (Table2).

Accuracy and precision

The accuracy and precision of the method were confirmed by performing five measurements of different drug concentrations. The value of the recovery and relative standard deviation were good and within the acceptable limits. That demonstrated that the method was of good efficacy. The results are presented in Table 3.

Table 3 Accuracy and precision for the determination of CLN.HCL in bulk powder by the proposed method:

Analysis of Clindamycin Hydrochloride in capsules

To estimate CLN.HCl in capsules, an advanced kinetic spectrophotometric method was used to identify Clindamycin in drug samples, and the results were summarized in Table 4.

Table 4 Estimation of CLN.HCl in their pharmaceutical preparations using the proposed kinetic methods and reference methods:

The proposed kinetic spectrophotometric method has the advantage of not interfering with excipients in pharmaceutical forms. The results of F and T-tests were shown in Table 4.

When the results obtained using the proposed method were compared with those obtained when applying the reference method[3]. The results were within acceptable limits, indicating that the proposed method is accurate because there is no significant difference between the proposed method and the reference method.

Conclusion

The proposed method is easy, fast, inexpensive, environmentally friendly and does not use any organic materials or reagents.

It is also having good recovery, accuracy and precision. The method can be used in the routine determination of clindamycin as a raw material or capsules.

The results obtained indicate that there is no interference with the excipients.

the proposed method is the first kinetic spectrophotometric study used to determine the concentration of clindamycin hydrochloride. All analytical reagents are reasonably priced, and the present method is environmentally safe because it doesn’t need any organic reagents or solvents, it is free extractive and also very sensitive comparing with the other spectrophotometric methods.

Availability of data and materials

The article includes the sources of all materials which was used in the research. The data are available from the corresponding author on reasonable request.

References

  1. Tehrani MB, Namadchian M, Vatan SF, Souri E (2013) Derivative spectrophotometric method for simultaneous determination of clindamycin phosphate and tretinoin in pharmaceutical dosage forms. DARU J Pharm Sci 21(1):1–7

    Google Scholar 

  2. Wayne PA (2011) Clinical and laboratory standards institute. In: Performance standards for antimicrobial susceptibility testing, pp 100–121

  3. The United States pharmacopeia 29 National formulary24. Rockville (MD) (2006), p 537

  4. Mifsud M, Vella J, Ferrito V, Serracino-Inglott A, Azzopardi LM, Bartolo NS et al (2014) A simple HPLC-UV method for the determination of clindamycin in human plasma. J Chem Pharm Res 6(1):696–704

    CAS  Google Scholar 

  5. Olbrich J, Corbett J (2013) Development and utilization of reversed phase high performance liquid chromatography methods for a series of therapeutic agents. Mod Chem Appl 1(2):1–6

    CAS  Google Scholar 

  6. Modi PB, Shah NJ (2014) Novel stability-indicating RP-HPLC method for the simultaneous estimation of clindamycin phosphate and adapalene along with preservatives in topical gel formulations. Sci Pharm 82(4):799–814

    Article  CAS  Google Scholar 

  7. Batzias GC, Delis GA, Koutsoviti-Papadopoulou M (2004) A new HPLC/UV method for the determination of clindamycin in dog blood serum. J Pharm Biomed Anal 35(3):545–554

    Article  CAS  Google Scholar 

  8. Stanković M, Savić V, Marinković V (2013) Determination of clindamycin phosphate in different vaginal gel formulations by reverse phase high performance liquid chromatography. Acta Facultatis Medicae Naissensis 30(2):63–71

    Article  Google Scholar 

  9. Wu GK, Gupta A, Khan MA, Faustino PJ (2013) Development and application of a validated HPLC method for the determination of clindamycin palmitate hydrochloride in marketed drug products: an optimization of the current USP methodology for assay. J Anal Sci Methods Instrum 3(4):202–211

    Google Scholar 

  10. Rizk MS, Merey HA, Tawakkol SM, Sweilam MN (2013) New potentiometric determination of clindamycin hydrochloride in pharmaceuticals. Res Rev Electrochem 4(5):161–167

    CAS  Google Scholar 

  11. Flurer CL, Wolnik KA (1994) Chemical profiling of pharmaceuticals by capillary electrophoresis in the determination of drug origin. J Chromatogr A 674(1–2):153–163

    Article  CAS  Google Scholar 

  12. Dehouck P, Van Schepdael A, Roets E, Hoogmartens J (2001) Analysis of clindamycin by micellar electrokinetic chromatography with a mixed micellar system. J Chromatogr A 932(1–2):145–152

    Article  CAS  Google Scholar 

  13. Shao X, Xie X, Liu Y, Song Z (2006) Rapid determination of clindamycin in medicine with myoglobin–luminol chemiluminescence system. J Pharm Biomed Anal 41(2):667–670

    Article  CAS  Google Scholar 

  14. Norouzi P, Larijani B, Ezoddin M, Ganjali MR (2008) Sub-second adsorption for the fast sub-nanomolar monitoring of Clindamycin in its pure and pharmaceutical samples by fast Fourier transformation with the use of continuous cyclic voltammetry at an Au microelectrode in a flowing system. Mater Sci Eng C 28(1):87–93

    Article  CAS  Google Scholar 

  15. Habib IHI, Rizk MS, El-Aryan TR (2011) Determination of clindamycin in dosage forms and biological samples by adsorption stripping voltammetry with carbon paste electrode. Pharm Chem J 44(12):705

    Article  CAS  Google Scholar 

  16. Elzanfaly ES, Zaazaa HE, Merey HA (2013) Ion selective phosphotungestate and β-cyclodextrin based membrane electrodes for stability-indicating determination of midodrine hydrochloride. Acta Chim Slov 60(2):256–262

    CAS  PubMed  Google Scholar 

  17. El-Yazbi FA, Blaih SM (1993) Spectrophotometric and titrimetric determination of clindamycin hydrochloride in pharmaceutical preparations. Analyst 118(5):577–579

    Article  CAS  Google Scholar 

  18. Amin AS (1995) Spectrophotometric and conductometric determination of clindamycin hydrochloride in pure form and in pharmaceutical preparations. Analusis 8(23):415–417

    Google Scholar 

  19. Khateeb M, Elias B, Al Rahal F (2015) Validated spectrophotometric method to Assay of B6 and B3 vitamins in pharmaceutical forms using potassium iodide and potassium iodate. Int Lett Chem Phys Astron 60:113–119

    Article  Google Scholar 

  20. Sakur AA, Affas S (2017) Validated spectrophotometric method to determine vardenafil and sildenafil in pharmaceutical forms using potassium iodide and potassium iodate. Int J Pharm Pharm Sci 9(11):65–69

    Article  CAS  Google Scholar 

  21. Khateeb M, Elias B, Adi S (2016) A novel use of 3-methyl-2-benzothiazolinone hydrazone hydrochloride monohydrate for kinetic spectrophotometric determination of captopril in pharmaceutical formulations. Int Lett Chem Phys Astron 71:29–39

    Article  Google Scholar 

  22. Moustafa I, Khateeb M, Alhamed O (2016) Kinetic spectrophotometric method for determination of vanadium in syrian oil using 1,5-diphenylcarbazide reagent. Int Lett Chem Phys Astron 67:42–49

    Article  Google Scholar 

Download references

Acknowledgements

Not applicable

Funding

There are no sources of funding.

Author information

Authors and Affiliations

Authors

Contributions

S.A performed The experiments and wrote the article. A.A.S. provided reagents and helped to review data. All authors read and approved the final manuscript.

Corresponding author

Correspondence to Shaza Affas.

Ethics declarations

Ethics approval and consent to participate

Not applicable.

Consent for publication

Not applicable.

Competing interests

The authors declare that they have no competing interests.

Additional information

Publisher's Note

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Rights and permissions

Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/. The Creative Commons Public Domain Dedication waiver (http://creativecommons.org/publicdomain/zero/1.0/) applies to the data made available in this article, unless otherwise stated in a credit line to the data.

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Affas, S., Sakur, A.A. Validated green spectrophotometric kinetic method for determination of Clindamycin Hydrochloride in capsules. BMC Chemistry 15, 29 (2021). https://0-doi-org.brum.beds.ac.uk/10.1186/s13065-021-00755-0

Download citation

  • Received:

  • Accepted:

  • Published:

  • DOI: https://0-doi-org.brum.beds.ac.uk/10.1186/s13065-021-00755-0

Keywords